daq_control_help
Table of Contents
Old DAQ Control
Alias daqcontrol or slowcontrol
Example of alias one can define to use daqcmd.py script
Slow Control
alias slccontrol="export DAQLOGIN=cmsLyon:RXXX_YYY;export DAQURL=https://ilcconfdb.yyy.fr/config-content/slow_control_dome_2;/opt/lydaq/qt/daqcmd.py"
Daq control with Oracle
alias daqcontrol="export DAQLOGIN=cmsLyon:RXXX_YYY;export DAQURL=https://ilcconfdb.yyyy.fr/config-content/diftest_bakelite_2;/opt/lydaq/qt/daqcmd.py"
Daq control with MongoDB
alias dqmg="export MGDBLOGIN=acqilc/RXXX_YYY@lyozzzzz:27017@LYONROC;export DAQMONGO=diftest_bakelite:2;/opt/lydaq/qt/daqcmd.py"
daqcontrol.py Object
All the access to the daq is described in an object called fdaqClient in the daqcontrol module.
Detailed documentation can be found in daqcontrol.pdf
The object is either used in command line (daqcmd.py script or with a pyQt interface (daqqt.py)
daqcmd.py script
The main script to access with command line the DAQ is daqcmd.py:
usage: daqcmd.py [-h]
[--available | --app-info | --webstatus | --jc-create | --jc-kill | --jc-destroy | --jc-start | --jc-restart | --jc-status | --jc-info | --jc-appcreate | --daq-create | --daq-discover | --daq-setparameters | --daq-getparameters | --daq-forceState | --daq-services | --daq-state | --daq-initialise | --daq-configure | --daq-startrun | --daq-stoprun | --daq-destroy | --daq-difstatus | --daq-tdcstatus | --daq-evbstatus | --daq-dbstatus | --daq-downloaddb | --dif-setgain | --dif-setthreshold | --dif-ctrlreg | --feb-resettdc | --feb-calibdac | --feb-scurve | --feb-setvth | --feb-setmask | --feb-settdcmode | --feb-settdcdelays | --feb-lutcalib | --feb-lutdraw | --histo-draw | --trig-status | --trig-reset | --trig-pause | --trig-resume | --ecal-pause | --ecal-resume | --trig-spillon | --trig-spilloff | --trig-beam | --trig-spillregister | --trig-calibon | --trig-calibcount | --trig-rearm | --trig-hardreset | --trig-setregister | --trig-getregister | --trig-tdcreset | --slc-create | --slc-initialise | --slc-configure | --slc-start | --slc-stop | --slc-lvon | --slc-lvoff | --slc-lvstatus | --slc-hvstatus | --slc-vset | --slc-iset | --slc-rampup | --slc-hvon | --slc-hvoff | --slc-clearalarm | --slc-ptstatus | --slc-humstatus | --slc-ptcor]
[--config CONFIG] [--socks SOCKPORT] [--dbstate DBSTATE]
[--ctrlreg CTRLREG] [--version] [--state FSTATE]
[--clock CLOCK] [--directory DIRECTORY] [--vth VTH]
[--mask MASK] [--gain GAIN] [--B0 B0] [--B1 B1] [--B2 B2]
[--v0 V0] [--p0 P0] [--t0 T0] [--tdc TDC] [--channel CHANNEL]
[--first FIRST] [--last LAST] [--step STEP]
[--voltage VOLTAGE] [--current CURRENT] [--ramp RAMP]
[--account ACCOUNT] [--period PERIOD] [--spillon SPILLON]
[--spilloff SPILLOFF] [--lines LINES] [--host HOST]
[--name NAME] [--jobname JOBNAME] [--jobpid JOBPID]
[--value VALUE] [--address ADDRESS] [--active ACTIVE]
[--dead DEAD] [--asic ASIC] [--feb FEB]
[--dbversion DBVERSION] [-v] [--comment COMMENT]
optional arguments:
| Command | Description |
| -h, –help | show this help message and exit |
| –available | Check availability of daq,jobcontrol and slowcontrol |
| –app-info | Check availability of daq,jobcontrol and slowcontrol |
| –webstatus | Check availability of daq,jobcontrol,slowcontrol and |
| Ecal web servers | |
| –jc-create | Loads configuration in all jobcontrol process |
| –jc-kill | kill all running processes |
| –jc-destroy | delete all jobcontrol configuration |
| –jc-start | start all controled processes described in  DAQCONFIG file to the DAQ |
| –daq-getparameters | get the parameters described in $DAQCONFIG file to the DAQ |
| –daq-forceState | force the sate name of the FDAQ with the –state option, ex –forceState –state=DISCOVERED |
| –daq-services | Send INITIALISE/CONFIGURE transition to services application (MDCC,DB,BUILDER mainly) |
| –daq-state | display DAQ state |
| –daq-initialise | Initialise FDAQ, data source discovery and Builderfinal configuration |
| –daq-configure | Configure FDAQ, front end ASICs configuration |
| –daq-startrun | start the run –comment=“my comment” |
| –daq-stoprun | stop the run |
| –daq-destroy | destroy the readout, back to the PREPARED state |
| –daq-difstatus | display DAQ status of all SDHCAL DIF |
| –daq-tdcstatus | display DAQ status of all FEBCMS TDC |
| –daq-evbstatus | display event builder status |
| –daq-dbstatus | get current run and state from db |
| –daq-downloaddb | download the dbsate specified in –dbstate=state |
| –dif-setgain | change the gain of HARDROC2 and reconfigure chips with –gain=xxx |
| –dif-setthreshold | change the threholds of HARDROC2 and reconfigure chips with –B0=xxx –B1=yyy –B2=zzz |
| –dif-ctrlreg | set the SDHCAL DIF ctrlregister specified with –ctrlreg=register |
| –feb-resettdc | Send Reset to all FEB TDC |
| –feb-calibdac | Start a PETIROC calibdac run |
| –feb-scurve | Start a PETIROC scurve run |
| –feb-setvth | change the VTHTIME threshold of PETIROC2 andreconfigure chips with -vth=xxx |
| –feb-setmask | change the MASK of PETIROC2 reconfigure chips with -mask=xxx |
| –feb-settdcmode | change the trigger mode before starting the run with –value=1 (trigger Only)/0 (all) |
| –feb-settdcdelays | change the PETIROC mode before starting the run with –active=1-255, –dead=1-255 |
| –feb-lutcalib | Calibrate –tdc=i –channel=k |
| –feb-lutdraw | Calibrate –tdc=i –channel=k |
| –histo-draw | Draw histo –name=histo |
| –trig-status | display trigger (MDCC) counter status |
| –trig-reset | reset trigger (MDCC) counter |
| –trig-pause | trigger (MDCC) soft veto |
| –trig-resume | release trigger (MDCC) soft veto |
| –ecal-pause | (Obsolete) Ecal soft veto |
| –ecal-resume | (Obsolete) release Ecal soft veto |
| –trig-spillon | set spill nclock on with –clock=nc (20ns) |
| –trig-spilloff | set spill nclock off with –clock=nc (20ns) |
| –trig-beam | set beam length to nclock with –clock=nc (20ns) |
| –trig-spillregister | set the value of the spill register (FEB CMS) (32/64 for beamtest or cosmic) –value=xx |
| –trig-calibon | set the value of the calibon register (FEB calibration) –value=xx |
| –trig-calibcount | set the value of the calibcount (FEB calibration) register –value=xx |
| –trig-rearm | reload calib (FEB calibration) |
| –trig-hardreset | send a hard reset to mezzanines |
| –trig-setregister | set the value of the MDCC register –value=xx –address=yy |
| –trig-getregister | get the value of the MDCC register –address=yy |
| –trig-tdcreset | hard reset of TDC (FEB) counters |
| –slc-create | Send a CREATE transition to FSLOW app (parsing of configuration) |
| –slc-initialise | Send a INITIALISE transition to FSLOW (auto discovery and CREATE transition to all controlled apps) |
| –slc-configure | Send a CONFIGURE transition to FSLOW (configuration of all controlled apps) |
| –slc-start | Send a START transition to all monitorApplication controlled |
| –slc-stop | Send a STOP transition to all monitorApplication controlled |
| –slc-lvon | put Zup LV ON |
| –slc-lvoff | put Zup LV OFF |
| –slc-lvstatus | Dump LV status |
| –slc-hvstatus | display hvstatus of all channel of the wiener crate |
| –slc-vset | set the voltage V of channel i to k with –first=i –last=k –voltage=V |
| –slc-iset | set the current limit I (microA) of channel i to k with –first=i –last=k –current=I |
| –slc-rampup | set the ramp (V/S) of channel i to k with –first=i –last=k –ramp=r |
| –slc-hvon | set the voltage ON of channel i to k with –first=i –last=k |
| –slc-hvoff | set the voltage OFF of channel i to k with –first=i –last=k |
| –slc-clearalarm | Clear alarm of channel i to k with –first=i –last=k |
| –slc-ptstatus | display the P and T from the BMP183 readout |
| –slc-humstatus | display the Humidity and T from the HIH8000 readout |
| –slc-ptcor | display the needed voltage for –v0=v –p0=p (mbar) –t0=t (K) |
| parameters | Description |
| –config CONFIG | json config file |
| –socks SOCKPORT | use SOCKS port |
| –dbstate DBSTATE | set the dbstate |
| –ctrlreg CTRLREG | set the Control register in hexa |
| –version | show program's version number and exit |
| –state FSTATE | set the Daq state |
| –clock CLOCK | set the number of 20 ns clock |
| –directory DIRECTORY | shm publisher directory |
| –vth VTH | set the vth for chips |
| –mask MASK | set the mask for chips |
| –gain GAIN | set the gain for chips |
| –B0 B0 | set the B0 for chips |
| –B1 B1 | set the B1 for chips |
| –B2 B2 | set the B2 for chips |
| –v0 V0 | reference hv |
| –p0 P0 | reference P |
| –t0 T0 | reference T |
| –tdc TDC | set the tdc process |
| –channel CHANNEL | set the hvchannel |
| –first FIRST | set the first hvchannel |
| –last LAST | set the last hvchannel |
| –step STEP | set the step of the calibration |
| –voltage VOLTAGE | set the hv voltage |
| –current CURRENT | set the hv current |
| –ramp RAMP | set the hv ramp |
| –account ACCOUNT | set the Slow Control mysql account |
| –period PERIOD | set the temporistaion period (s) |
| –spillon SPILLON | spill on |
| –spilloff SPILLOFF | spilloff |
| –lines LINES | set the number of lines to be dump |
| –host HOST | host for log |
| –name NAME | application name |
| –jobname JOBNAME | job name |
| –jobpid JOBPID | job pid |
| –value VALUE | value to pass |
| –address ADDRESS | address to pass |
| –active ACTIVE | active time of Petiroc |
| –dead DEAD | dead time of Petiroc |
| –asic ASIC | asic header of Petiroc |
| –feb FEB | FEB id |
| –dbversion DBVERSION | DB state version |
| -v, –verbose | Raw Json output |
| –comment COMMENT | Comment for start run |
daq_control_help.txt · Last modified: 2021/07/10 23:21 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
