===== Calibration Board 3 (FE # 4) =====
==== Resistance 100 kOhm ====
=== Pedestals ===
* Aucun cable d'injection connecte
* Piste par piste , 737733
* Tous ensemble ,737735, 737738. Tres peu de bruits, tous alignes a 361
* On allume le gene, rien de connecte
* 737739, un pic de bruit apparait!
* On connecte la masse du gene au plan superieur
* Des masses de partout!!!
=== Injection ====
* 500 mV 737769
canal 2 395
canal 14 390
* 200 mV 737770
canal 2 371
canal 14 370
* 150 mV 737771
canal 2 367
canal 14 366
* 120 mV 737772
canal 2
canal 14
{{::calibration_board3_piste71.jpg?200|}}
On obtient 12.3 mV par VTH count du cote large
et 14.7 mV par VTH du cote oppose
Donc entre 6 et 7 fC (facteur 2 du au partage des charges) par DAC.
Le piedestal mesure est a 362, extrapole a 355 on est sans doute pas completement lineaire a basse injection
Si on regarde le rapport des signaux transmis et proche on a
{{::injection_5pc_cote_large_pcb_fin--00000.png?200|}}
On retrouve le rapport mesure de 12.3/14.7 ~ 84 %
=== Etude de l'efficacite ===
Seuil minimal 368 => environ 7*7.3=51 fC
Injection cote large, en comptant un coup de "turn on" on s'attend a etre efficace du cote injection a
(369-355.26)/0.0814 = 169 mV
et des deux cotes a
(369-356.0)/0.0679 = 191 mV
On obtient:
^ run ^ Injection(fC) ^ N trg ^ N 2 ^ N 14 ^ Eff ^ deFF ^ Eff XY ^ deff XY ^ dt (ns) ^ RMS dt (ns) ^
|737785|150|4784|3315|130|69.29| 0.67| 2.72| 0.24|-17.66|0.337|
|737784|160|7776|7707|4048|99.11| 0.11|52.06| 0.57|-17.62|0.304|
|737782|170|5797|5794|5240|99.95| 0.03|90.39| 0.39|-17.50|0.280|
|737786|180|16367|16364|14730|99.98| 0.01|90.00| 0.23|-17.66|0.263|
|737787|190|11414|11414|11304|100.00| 0.00|99.04| 0.09|-17.61|0.215|
|737788|200|14157|14157|14147|100.00| 0.00|99.93| 0.02|-17.57|0.204|
|737789|250|14939|14939|14939|100.00| 0.00|100.00| 0.00|-17.61|0.172|
|737790|300|13358|13358|13358|100.00| 0.00|100.00| 0.00|-17.57|0.173|
|737791|500|11894|11894|11894|100.00| 0.00|100.00| 0.00|-17.40|0.124|
|737792|1000|15454|15454|15454|100.00| 0.00|100.00| 0.00|-17.16|0.071|
|737795|160|20792|20792|181|100.00| 0.00| 0.87| 0.06| 0.04|0.239|
|737798|170|13197|13197|654|100.00| 0.00| 4.96| 0.19| 0.15|0.235|
|737799|180|27589|27589|6367|100.00| 0.00|23.08| 0.25| 0.12|0.225|
|737800|190|15538|15538|8984|100.00| 0.00|57.82| 0.40| 0.06|0.235|
|737794|200|13980|13980|13449|100.00| 0.00|96.20| 0.16| 0.03|0.190|
|737801|210|27889|27889|27460|100.00| 0.00|98.46| 0.07|-0.04|0.178|
|737802|220|14420|14420|14340|100.00| 0.00|99.45| 0.06|-0.18|0.199|
|737803|300|11582|11582|11577|100.00| 0.00|99.96| 0.02|-0.51|0.173|
^Run ^Injection ^Events ^Efficiency ^2 cotes ^Resolution (ps) ^
|737782|170| 2956| 100|90.2 | 278|
|737784|160| 5591| 99.6| 57.2 | 306|
|737785|150| 2152| 71.7| 4|330|
|737786|180| 16367| 100| 90|265|
|737787|190| 11414| 100| 99|220|
|737788|200| 14157| 100| 100|210|
|737789|250| 14900| 100| 100|178|
|737790|300| 13359| 100| 100|174|
|737791|500| 11894| 100| 100|124|
|737792|1000| 15454| 100| 100|69|
Injection cote 14 (etroit)
^Run ^Injection ^Events ^Efficiency ^2 cotes ^Resolution (ps) ^
|737794|200| 13980| 100|96.2 | 204|
|737795|160| 20792| 100|0.9 | 270|
|737798|170| 13197| 100| 5.0 | 267|
|737799|180| 27589| 100| 23.1 | 243|
|737800|190| 15538| 100| 57.8 | 247|
|737801|210| 27889| 100| 98.5 | 188|
|737802|220| 14340| 100| 99.5 | 207|
|737803|300| 11583| 100| 100 | 178|
Delat T -17.6 et -0.5 donc 17.1=2 x dt => dt =8.6 compatible avec la mesure des pulses (8.3)
On change de piste 73
et on s'arrache la tete, le delai trigger / pulse doit etre regle a 2.5 ns pres car on peut tomber sur le temps mort du TDC....
Run 737813 , 250 fC cote etroit on n'est pas pleinement efficace des deux cotes (78 %)
737818 200 mV de l'autre cote
737819 210 mV
737820 220 mV (69 %)
On a donc quasiment 50 fC d'eccart entre les deux pistes... A comprendre est ce du a un probleme de gain ?
==== Resistance 150 kOhm ====
=== pedestals ===
* separees all at 31
Run 737897
[329.8383850069412, 338.8306754221388, 344.2252510760402, 342.5212249848393, 349.84411239964317, 347.26503960608005, 345.5721327967807, 344.1441947565543, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 323.52208201892745, 328.007655393053, 331.68205405405405, 330.8333719046517, 330.7964367816092, 326.54009433962267, 319.96534161490683, 322.15447637140824]
Alignment to : 324.965341615
[29, 26, 25, 25, 23, 23, 24, 25, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 31, 30, 29, 29, 29, 30, 33, 32]
Run verification 737898
Pedestal centre a 327
[325.8353293413174, 326.7075669383004, 327.053392259914, 326.0224846328049, 328.6779397705545, 326.76496800731263, 329.03019970774477, 328.0180568499534, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 326.5226199353716, 327.0759254892714, 329.03002257336345, 325.8924501424501, 327.6408518877057, 325.3631103911132, 327.0556603773585, 325.9967320261438]
Alignment to : 330.363110391
[33, 32, 32, 32, 32, 32, 31, 32, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 32, 32, 31, 33, 32, 33, 32, 32]
Pedestal All together 737899
== Injection piste 71 cote TDC 2 ==
^ run ^ Injection (fC) ^ turn On 2 ^ turn on 14 ^
|737908|200|349|342|
|737907|250|355.5|348|
|737903| 300|362|353|
|737905| 350|370|359.5|
|737904| 400|377|366|
|737906| 500|390|377|
{{ :fe4_150k_calib.png?500 |}}
== Etude de l'efficacité ==
Seuil a **343**
**(343-327)/0.139 =115 fC /2 => 57.5 fC par canal**
^ run ^ Injection(fC) ^ N trg ^ N 2 ^ N 14 ^ Eff ^ deFF ^ Eff XY ^ deff XY ^ $\Delta T $(ns) ^ $\sigma $ dt (ns) ^
|737910|160|2381|1989|76|83.54| 0.76| 3.19| 0.36|-17.21|0.402|
|737911|170|2380|2302|349|96.72| 0.36|14.66| 0.73|-17.34|0.377|
|737912|180|2383|2375|964|99.66| 0.12|40.45| 1.01|-17.42|0.326|
|737913|190|2381|2381|1713|100.00| 0.00|71.94| 0.92|-17.50|0.292|
|737914|200|2383|2383|2180|100.00| 0.00|91.48| 0.57|-17.46|0.252|
|737915|210|2381|2381|2331|100.00| 0.00|97.90| 0.29|-17.40|0.228|
|737916|220|2381|2381|2371|100.00| 0.00|99.58| 0.13|-17.38|0.220|
|737917|230|2383|2383|2374|100.00| 0.00|99.62| 0.13|-17.44|0.239|
|737918|250|2381|2381|2381|100.00| 0.00|100.00| 0.00|-17.60|0.192|
|737919|500|2381|2381|2381|100.00| 0.00|100.00| 0.00|-17.40|0.077|
|737920|1000|2382|2382|2381|100.00| 0.00|99.96| 0.04|-17.46|0.051|
{{ :fe4_150k_piste71.png?500 |}}
{{ :fe4_150k_piste71_res.png?500 |}}
--- //[[laurent.mirabito@gmail.com|mirabito]] 2017/11/26 15:40//
===== Calibration Board 2 =====
==== Resistance 100 kOhm ===
=== Pedestal ===
* Piste par piste
Run 737827 tous les canaux a 31 fichier PR2_TDC7_737733_Board2.json
Correction
dac[i]=int(round(old[i]+(med-ped[i])*1./2.97))
J'ai mis un facteur 1 car je crois que le rapport a utiliser et celui que m'avait donne Nathalie
On obtient pour le PETIROC:
[526.4389607160616, 520.36827148111, 517.0154950869237, 537.4540172642762, 542.3748160863169, 535.4546346248161, 533.0708641975309, 535.0666831316374, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 516.0272040302267, 529.4941191191191, 515.4653403403404, 523.6680430430431, 524.3245158242796, 522.5375281461096, 531.0689612326044, 519.7234042553191]
[29, 31, 32, 25, 24, 26, 27, 26, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 32, 28, 33, 30, 30, 30, 27, 31]
Run apres realignement 737829
[520.9286067193676, 521.4198548812665, 520.7046224588577, 520.1427212178877, 520.2083950617284, 520.3633200795229, 520.2205846528624, 520.0534304047384, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 522.8704023697852, 520.5618313013188, 522.772006827603, 520.4732377538829, 522.0271739130435, 520.8262012012012, 519.772546583851, 521.0904347826087]
Alignment to : 524.772546584
[32, 32, 32, 33, 33, 32, 33, 33, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 32, 32, 32, 32, 32, 32, 33, 32]
Avec toutes les pistes alignes 727830
On obtient :
[522.8711790393013, 521.619812583668, 521.7325301204819, 522.7821482602118, 522.7918313570487, 522.591849935317, 522.5179487179487, 523.1693766937669, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 522.5348258706467, 522.4192182410424, 522.8073566084788, 523.1639035418236, 522.8275541795666, 522.2118537200504, 522.1827284105132, 523.0398457583548]
En prenant 523 comme piedestal et 1.5 de bruit on essaie une coupure a 531
Trop bas
on met 536
=== Injection ===
|737832| 200 | 551 | 533|
|737833| 250 | 559 | 533 |
|737834| 300 | 568.5| 532|
|737835| 350| 580.6| 533|
On fait un essai en supprimant la 100 kOhm
Non concluant, om augmente le gain, le pedestal ~ 325, bcp de bruit (737843)
Coupure a 380 => 100 % efficacite pour 190 mV injecte
==== Resistance 68 kOhm ====
Ca ne marche pas
==== Resistance 150 kOhm ====
=== Pedestals piste / piste 737865 ===
[484.5533201678598, 473.86687983843825, 467.43546365914784, 495.70765113350126, 504.15454134658836, 493.12993716337525, 489.69016239115086, 493.90647994303345, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 467.59760403530896, 487.1604968339016, 466.51782077393074, 477.57714285714286, 478.68060200668896, 476.5175438596491, 490.18785485065416, 471.2535651738804]
Alignment to : 471.517820774
[27, 30, 32, 23, 20, 24, 25, 23, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 32, 26, 33, 29, 29, 29, 25, 31]
Run de verification 737866
=== Pedestal alltogether ===
737868
pedestal 471 , bruit < 1
On branche le cable d'injection
737869 , le bruit augmente a 1.7
=== Injection ===
Injection cote large
^run ^ Injection (mV) ^ cote large ^ Etroit ^
|737872|500|559|550|
|737873|400|541|534|
|737874|350|532|525|
|737875|300|522|516|
|737876|250|513|505.5|
|737877|225|507|502|
|737878|200|502|497|
{{ :fe2_150k_calib.png?500 |}}
On met le seuil a **494**
**(494-471)/0.1845 = 125 fC /2 => 62.5 fC de seuil par canal**
^ run ^ Injection(fC) ^ N trg ^ N 2 ^ N 14 ^ Eff ^ deFF ^ Eff XY ^ deff XY ^ dt (ns) ^ RMS dt (ns) ^
|737880|160|7748|6618|2007|85.42| 0.40|25.90| 0.50|-17.30|0.336|
|737881|170|4103|4020|2651|97.98| 0.22|64.61| 0.75|-17.36|0.307|
|737882|180|5100|5096|4476|99.92| 0.04|87.76| 0.46|-17.40|0.310|
|737883|190|4829|4829|4672|100.00| 0.00|96.75| 0.26|-17.42|0.291|
|737884|200|3361|3361|3216|100.00| 0.00|95.69| 0.35|-17.46|0.277|
|737885|210|3268|3265|3227|99.91| 0.05|98.75| 0.19|-17.49|0.228|
|737886|220|3408|3403|3313|99.85| 0.07|97.21| 0.28|-17.49|0.193|
|737887|250|3096|3096|3095|100.00| 0.00|99.97| 0.03|-17.52|0.203|
On des burst de bruits.... ce qui explique les fluctuations
Si on met le seuil a 496 et 200 mV
^ run ^ Injection(fC) ^ N trg ^ N 2 ^ N 14 ^ Eff ^ deFF ^ Eff XY ^ deff XY ^ dt (ns) ^ RMS dt (ns) ^
|737892|210|3095|3095|3034|100.00| 0.00|98.03| 0.25|-17.45|0.288|
|737888|200|3093|3093|3008|100.00| 0.00|97.25| 0.29|-17.46|0.298|
|737889|190|3094|3092|2718|99.94| 0.05|87.85| 0.59|-17.39|0.316|
|737890|180|3094|3041|2040|98.29| 0.23|65.93| 0.85|-17.37|0.308|
|737891|170|3097|2611|699|84.31| 0.65|22.57| 0.75|-17.31|0.347|
{{ :calib_ipnl:fe2_150k_piste71_eff.png?500 |}}
Resolution la plus mauvaise observee ~ 0.3/8.6 => 5 cm
Su la on observe:
* Seuil minimal de detection electronique => 90 fC, Q injected 180 fC
* Seuil minimal de mesure X,Y Q injected 200 fC
Les résultats sont quasiment identiques à ceux mesurés avec le Board 3 (FE #4)
--- //[[laurent.mirabito@gmail.com|mirabito]] 2017/11/23 06:35//
--- //[[laurent.mirabito@gmail.com|DAQ user]] 2017/11/27 12:12//